the fix for Searching for Signal and E34, E35 & Optus Aurora

[foxtel employee]

Hi All, (sorry its a bit late but might still help)

Below is the fix for Searching for Signal and E34, E35 & Optus Aurora.

Here is an update on the fix for Searching for Signals

Press Menu
Advanced options
Change dish installation
9949
Signal setup
1 (home)

This should read as follows: If it doesn’t please change using the arrow buttons or number keypad on foxtel remote. Press OK once the below settings have been added. Then press exit once. Then select Tune & Re-scan and press OK. If an E16 appears after the Tune & Re-scan, initialize the Smart Card.

Signal source = enabled
LNB selection = 1
Freq = 12478
Symb rate 27800
Pol = Horizontal
FEC = 3/4

*****Please check the LNB Setup by doing as follows

Press Menu
Advanced options
Change dish installation
9949
LNB Configuration
LNB Setup 1

This should read as follows:

LNB Power: On
LNB Mode: Single frequency
LNB Frequency: 11300 (for old 11.3 LNB or change to 10700 if you have had new 10.7 LNB installed)


If you have had a tech out to your property anytime after 1st August 2003 you will have a 10.7 LNB


E34, E35 & Optus Aurora fix
The output will change to 38 so please take a note of the customer's output before performing this function
Menu
Advanced Options
Change Dish Install
Pin 9949
Reset to Factory Defaults
Press OK twice

If you have any problems, let us know. 131 999 (its not busy anymore)

[Wayne349]

That fix does'nt fix mine, the Frequeny 12478 Mhz is the one that it keeps
searching for the most and
my settings are identical to what you've posted.
I just changed from 22 to 18 and after 15 mins it was still searching for
that freq. ?
Signal strength is 80 to 85 %






"foxtel employee" <foxtel.employee.xne09@no-mx.forums.eyo.com.au> wrote in
message news:foxtel.employee.xne09@no-mx.forums.eyo.com.au...
>
> Hi All, (sorry its a bit late but might still help)
>
> Below is the fix for Searching for Signal and E34, E35 & Optus Aurora.
>
>
> Here is an update on the fix for Searching for Signals
>
> Press Menu
> Advanced options
> Change dish installation
> 9949
> Signal setup
> 1 (home)
>
> This should read as follows: If it doesn't please change using the
> arrow buttons or number keypad on foxtel remote. Press OK once the
> below settings have been added. Then press exit once. Then select Tune
> & Re-scan and press OK. If an E16 appears after the Tune & Re-scan,
> initialize the Smart Card.
>
> Signal source = enabled
> LNB selection = 1
> Freq = 12478
> Symb rate 27800
> Pol = Horizontal
> FEC = 3/4
>
> *****Please check the LNB Setup by doing as follows
>
> Press Menu
> Advanced options
> Change dish installation
> 9949
> LNB Configuration
> LNB Setup 1
>
> This should read as follows:
>
> LNB Power: On
> LNB Mode: Single frequency
> LNB Frequency: 11300 (for old 11.3 LNB or change to 10700 if you have
> had new 10.7 LNB installed)
>
>
> If you have had a tech out to your property anytime after 1st August
> 2003 you will have a 10.7 LNB
>
>
> E34, E35 & Optus Aurora fix
> The output will change to 38 so please take a note of the customer's
> output before performing this function
> Menu
> Advanced Options
> Change Dish Install
> Pin 9949
> Reset to Factory Defaults
> Press OK twice
>
> If you have any problems, let us know. 131 999 (its not busy anymore)
>
>
> --
> foxtel employee
> ------------------------------------------------------------------------
> foxtel employee's Profile:
http://forums.eyo.com.au/member.php?action=getinfo&userid=7843
> View this thread: http://forums.eyo.com.au/showthread.php?threadid=31448
>

[Wayne349]

"Wayne349" <apollo345@hotmail.com> wrote in message
news:3fc8615d$0$1731$5a62ac22@freenews.iinet.net.a u...
> That fix does'nt fix mine, the Frequeny 12478 Mhz is the one that it keeps
> searching for the most and
> my settings are identical to what you've posted.
> I just changed from 22 to 18 and after 15 mins it was still searching for
> that freq. ?
> Signal strength is 80 to 85 %
Thats Arena to National Geo Channel the 22 to 18
>
>
>
>
>
>
> "foxtel employee" <foxtel.employee.xne09@no-mx.forums.eyo.com.au> wrote in
> message news:foxtel.employee.xne09@no-mx.forums.eyo.com.au...
> >
> > Hi All, (sorry its a bit late but might still help)
> >
> > Below is the fix for Searching for Signal and E34, E35 & Optus Aurora.
> >
> >
> > Here is an update on the fix for Searching for Signals
> >
> > Press Menu
> > Advanced options
> > Change dish installation
> > 9949
> > Signal setup
> > 1 (home)
> >
> > This should read as follows: If it doesn't please change using the
> > arrow buttons or number keypad on foxtel remote. Press OK once the
> > below settings have been added. Then press exit once. Then select Tune
> > & Re-scan and press OK. If an E16 appears after the Tune & Re-scan,
> > initialize the Smart Card.
> >
> > Signal source = enabled
> > LNB selection = 1
> > Freq = 12478
> > Symb rate 27800
> > Pol = Horizontal
> > FEC = 3/4
> >
> > *****Please check the LNB Setup by doing as follows
> >
> > Press Menu
> > Advanced options
> > Change dish installation
> > 9949
> > LNB Configuration
> > LNB Setup 1
> >
> > This should read as follows:
> >
> > LNB Power: On
> > LNB Mode: Single frequency
> > LNB Frequency: 11300 (for old 11.3 LNB or change to 10700 if you have
> > had new 10.7 LNB installed)
> >
> >
> > If you have had a tech out to your property anytime after 1st August
> > 2003 you will have a 10.7 LNB
> >
> >
> > E34, E35 & Optus Aurora fix
> > The output will change to 38 so please take a note of the customer's
> > output before performing this function
> > Menu
> > Advanced Options
> > Change Dish Install
> > Pin 9949
> > Reset to Factory Defaults
> > Press OK twice
> >
> > If you have any problems, let us know. 131 999 (its not busy anymore)
> >
> >
> > --
> > foxtel employee
> > ------------------------------------------------------------------------
> > foxtel employee's Profile:
> http://forums.eyo.com.au/member.php?action=getinfo&userid=7843
> > View this thread: http://forums.eyo.com.au/showthread.php?threadid=31448
> >
>
>

[foxtel employee]

call 131 999 and ask to speak to tech support they can fix it

[Wayne349]

Already did that yesterday, was told it would be like it until sometime next
week as the conversion to digital was in progress and was interfering with
everyones the same and other people could'nt get say - FOX8 etc...
and if it was like it by the end of next week to ring back again.
Have notice just then, after the ungrade a while ago that the channels are
changing better and comming up quicker at the moment though, see how it
goes.





"foxtel employee" <foxtel.employee.xngbm@no-mx.forums.eyo.com.au> wrote in
message news:foxtel.employee.xngbm@no-mx.forums.eyo.com.au...
>
> call 131 999 and ask to speak to tech support they can fix it
>
>
> --
> foxtel employee
> ------------------------------------------------------------------------
> foxtel employee's Profile:
http://forums.eyo.com.au/member.php?action=getinfo&userid=7843
> View this thread: http://forums.eyo.com.au/showthread.php?threadid=31448
>

[Simmo]

ummmm really?
"xxx" <xxx@xxx.com> wrote in message news:3fc99607_1@news.iprimus.com.au...
> Conversion to digital , lol , Foxtel Satellite has been digital since day
> one.
> Try 12558 instead of 12478
>
>
> "Wayne349" <apollo345@hotmail.com> wrote in message
> news:3fc86e74$0$1744$5a62ac22@freenews.iinet.net.a u...
> > Already did that yesterday, was told it would be like it until sometime
> next
> > week as the conversion to digital was in progress and was interfering
with
> > everyones the same and other people could'nt get say - FOX8 etc...
> > and if it was like it by the end of next week to ring back again.
> > Have notice just then, after the ungrade a while ago that the channels
are
> > changing better and comming up quicker at the moment though, see how it
> > goes.
> >
> >
> >
> >
> >
> > "foxtel employee" <foxtel.employee.xngbm@no-mx.forums.eyo.com.au> wrote
in
> > message news:foxtel.employee.xngbm@no-mx.forums.eyo.com.au...
> > >
> > > call 131 999 and ask to speak to tech support they can fix it
> > >
> > >
> > > --
> > > foxtel employee
> >
> ------------------------------------------------------------------------
> > > foxtel employee's Profile:
> > http://forums.eyo.com.au/member.php?action=getinfo&userid=7843
> > > View this thread:
http://forums.eyo.com.au/showthread.php?threadid=31448
> > >
> >
> >
>
>

[thetron]

Yes
The signal is digital... Just not some of the camera and studio equipment
"Simmo" <blahblahblah@figpond.com> wrote in message
news:1Ngyb.33383$aT.10056@news-server.bigpond.net.au...
> ummmm really?
> "xxx" <xxx@xxx.com> wrote in message
news:3fc99607_1@news.iprimus.com.au...
> > Conversion to digital , lol , Foxtel Satellite has been digital since
day
> > one.
> > Try 12558 instead of 12478
> >
> >
> > "Wayne349" <apollo345@hotmail.com> wrote in message
> > news:3fc86e74$0$1744$5a62ac22@freenews.iinet.net.a u...
> > > Already did that yesterday, was told it would be like it until
sometime
> > next
> > > week as the conversion to digital was in progress and was interfering
> with
> > > everyones the same and other people could'nt get say - FOX8 etc...
> > > and if it was like it by the end of next week to ring back again.
> > > Have notice just then, after the ungrade a while ago that the channels
> are
> > > changing better and comming up quicker at the moment though, see how
it
> > > goes.
> > >
> > >
> > >
> > >
> > >
> > > "foxtel employee" <foxtel.employee.xngbm@no-mx.forums.eyo.com.au>
wrote
> in
> > > message news:foxtel.employee.xngbm@no-mx.forums.eyo.com.au...
> > > >
> > > > call 131 999 and ask to speak to tech support they can fix it
> > > >
> > > >
> > > > --
> > > > foxtel employee
> > >
> > ------------------------------------------------------------------------
> > > > foxtel employee's Profile:
> > > http://forums.eyo.com.au/member.php?action=getinfo&userid=7843
> > > > View this thread:
> http://forums.eyo.com.au/showthread.php?threadid=31448
> > > >
> > >
> > >
> >
> >
>
>

[thetron]

If the signal was anlogue anyone would be able to access it easly
"Simmo" <blahblahblah@figpond.com> wrote in message
news:1Ngyb.33383$aT.10056@news-server.bigpond.net.au...
> ummmm really?
> "xxx" <xxx@xxx.com> wrote in message
news:3fc99607_1@news.iprimus.com.au...
> > Conversion to digital , lol , Foxtel Satellite has been digital since
day
> > one.
> > Try 12558 instead of 12478
> >
> >
> > "Wayne349" <apollo345@hotmail.com> wrote in message
> > news:3fc86e74$0$1744$5a62ac22@freenews.iinet.net.a u...
> > > Already did that yesterday, was told it would be like it until
sometime
> > next
> > > week as the conversion to digital was in progress and was interfering
> with
> > > everyones the same and other people could'nt get say - FOX8 etc...
> > > and if it was like it by the end of next week to ring back again.
> > > Have notice just then, after the ungrade a while ago that the channels
> are
> > > changing better and comming up quicker at the moment though, see how
it
> > > goes.
> > >
> > >
> > >
> > >
> > >
> > > "foxtel employee" <foxtel.employee.xngbm@no-mx.forums.eyo.com.au>
wrote
> in
> > > message news:foxtel.employee.xngbm@no-mx.forums.eyo.com.au...
> > > >
> > > > call 131 999 and ask to speak to tech support they can fix it
> > > >
> > > >
> > > > --
> > > > foxtel employee
> > >
> > ------------------------------------------------------------------------
> > > > foxtel employee's Profile:
> > > http://forums.eyo.com.au/member.php?action=getinfo&userid=7843
> > > > View this thread:
> http://forums.eyo.com.au/showthread.php?threadid=31448
> > > >
> > >
> > >
> >
> >
>
>

[Simmo]

ummmm really?

"thetron" <getursel@adomain.com> wrote in message
news:3fca2cd7$0$15347$61c65585@uq-127creek-reader-02.brisbane.pipenetworks.com.au...
> If the signal was anlogue anyone would be able to access it easly
> "Simmo" <blahblahblah@figpond.com> wrote in message
> news:1Ngyb.33383$aT.10056@news-server.bigpond.net.au...
> > ummmm really?
> > "xxx" <xxx@xxx.com> wrote in message
> news:3fc99607_1@news.iprimus.com.au...
> > > Conversion to digital , lol , Foxtel Satellite has been digital since
> day
> > > one.
> > > Try 12558 instead of 12478
> > >
> > >
> > > "Wayne349" <apollo345@hotmail.com> wrote in message
> > > news:3fc86e74$0$1744$5a62ac22@freenews.iinet.net.a u...
> > > > Already did that yesterday, was told it would be like it until
> sometime
> > > next
> > > > week as the conversion to digital was in progress and was
interfering
> > with
> > > > everyones the same and other people could'nt get say - FOX8 etc...
> > > > and if it was like it by the end of next week to ring back again.
> > > > Have notice just then, after the ungrade a while ago that the
channels
> > are
> > > > changing better and comming up quicker at the moment though, see how
> it
> > > > goes.
> > > >
> > > >
> > > >
> > > >
> > > >
> > > > "foxtel employee" <foxtel.employee.xngbm@no-mx.forums.eyo.com.au>
> wrote
> > in
> > > > message news:foxtel.employee.xngbm@no-mx.forums.eyo.com.au...
> > > > >
> > > > > call 131 999 and ask to speak to tech support they can fix it
> > > > >
> > > > >
> > > > > --
> > > > > foxtel employee
> > > >
> >
> ------------------------------------------------------------------------
> > > > > foxtel employee's Profile:
> > > > http://forums.eyo.com.au/member.php?action=getinfo&userid=7843
> > > > > View this thread:
> > http://forums.eyo.com.au/showthread.php?threadid=31448
> > > > >
> > > >
> > > >
> > >
> > >
> >
> >
>
>

[Bassett]

He,s never heard of a analogue encripted service,,Dur.

"Simmo" <blahblahblah@figpond.com> wrote in message
news:vAtyb.34006$aT.10734@news-server.bigpond.net.au...
> ummmm really?
>
> "thetron" <getursel@adomain.com> wrote in message
>
news:3fca2cd7$0$15347$61c65585@uq-127creek-reader-02.brisbane.pipenetworks.c
om.au...
> > If the signal was anlogue anyone would be able to access it easly
> > "Simmo" <blahblahblah@figpond.com> wrote in message
> > news:1Ngyb.33383$aT.10056@news-server.bigpond.net.au...
> > > ummmm really?
> > > "xxx" <xxx@xxx.com> wrote in message
> > news:3fc99607_1@news.iprimus.com.au...
> > > > Conversion to digital , lol , Foxtel Satellite has been digital
since
> > day
> > > > one.
> > > > Try 12558 instead of 12478
> > > >
> > > >
> > > > "Wayne349" <apollo345@hotmail.com> wrote in message
> > > > news:3fc86e74$0$1744$5a62ac22@freenews.iinet.net.a u...
> > > > > Already did that yesterday, was told it would be like it until
> > sometime
> > > > next
> > > > > week as the conversion to digital was in progress and was
> interfering
> > > with
> > > > > everyones the same and other people could'nt get say - FOX8 etc...
> > > > > and if it was like it by the end of next week to ring back again.
> > > > > Have notice just then, after the ungrade a while ago that the
> channels
> > > are
> > > > > changing better and comming up quicker at the moment though, see
how
> > it
> > > > > goes.
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > > "foxtel employee" <foxtel.employee.xngbm@no-mx.forums.eyo.com.au>
> > wrote
> > > in
> > > > > message news:foxtel.employee.xngbm@no-mx.forums.eyo.com.au...
> > > > > >
> > > > > > call 131 999 and ask to speak to tech support they can fix it
> > > > > >
> > > > > >
> > > > > > --
> > > > > > foxtel employee
> > > > >
> > >
> > ------------------------------------------------------------------------
> > > > > > foxtel employee's Profile:
> > > > > http://forums.eyo.com.au/member.php?action=getinfo&userid=7843
> > > > > > View this thread:
> > > http://forums.eyo.com.au/showthread.php?threadid=31448
> > > > > >
> > > > >
> > > > >
> > > >
> > > >
> > >
> > >
> >
> >
>
>

[Simmo]

hmmmm
"Bassett" <bassett@bassettskennel.com.au> wrote in message
news:3fcb071d$1@dnews.tpgi.com.au...
> He,s never heard of a analogue encripted service,,Dur.
>
> "Simmo" <blahblahblah@figpond.com> wrote in message
> news:vAtyb.34006$aT.10734@news-server.bigpond.net.au...
> > ummmm really?
> >
> > "thetron" <getursel@adomain.com> wrote in message
> >
>
news:3fca2cd7$0$15347$61c65585@uq-127creek-reader-02.brisbane.pipenetworks.c
> om.au...
> > > If the signal was anlogue anyone would be able to access it easly
> > > "Simmo" <blahblahblah@figpond.com> wrote in message
> > > news:1Ngyb.33383$aT.10056@news-server.bigpond.net.au...
> > > > ummmm really?
> > > > "xxx" <xxx@xxx.com> wrote in message
> > > news:3fc99607_1@news.iprimus.com.au...
> > > > > Conversion to digital , lol , Foxtel Satellite has been digital
> since
> > > day
> > > > > one.
> > > > > Try 12558 instead of 12478
> > > > >
> > > > >
> > > > > "Wayne349" <apollo345@hotmail.com> wrote in message
> > > > > news:3fc86e74$0$1744$5a62ac22@freenews.iinet.net.a u...
> > > > > > Already did that yesterday, was told it would be like it until
> > > sometime
> > > > > next
> > > > > > week as the conversion to digital was in progress and was
> > interfering
> > > > with
> > > > > > everyones the same and other people could'nt get say - FOX8
etc...
> > > > > > and if it was like it by the end of next week to ring back
again.
> > > > > > Have notice just then, after the ungrade a while ago that the
> > channels
> > > > are
> > > > > > changing better and comming up quicker at the moment though, see
> how
> > > it
> > > > > > goes.
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > > "foxtel employee"
<foxtel.employee.xngbm@no-mx.forums.eyo.com.au>
> > > wrote
> > > > in
> > > > > > message news:foxtel.employee.xngbm@no-mx.forums.eyo.com.au...
> > > > > > >
> > > > > > > call 131 999 and ask to speak to tech support they can fix it
> > > > > > >
> > > > > > >
> > > > > > > --
> > > > > > > foxtel employee
> > > > > >
> > > >
> >
> ------------------------------------------------------------------------
> > > > > > > foxtel employee's Profile:
> > > > > > http://forums.eyo.com.au/member.php?action=getinfo&userid=7843
> > > > > > > View this thread:
> > > > http://forums.eyo.com.au/showthread.php?threadid=31448
> > > > > > >
> > > > > >
> > > > > >
> > > > >
> > > > >
> > > >
> > > >
> > >
> > >
> >
> >
>
>

[Macros]

Change your default home transponder settings.
"Wayne349" <apollo345@hotmail.com> wrote in message
news:3fc8615d$0$1731$5a62ac22@freenews.iinet.net.a u...
> That fix does'nt fix mine, the Frequeny 12478 Mhz is the one that it keeps
> searching for the most and
> my settings are identical to what you've posted.
> I just changed from 22 to 18 and after 15 mins it was still searching for
> that freq. ?
> Signal strength is 80 to 85 %
>
>
>
>
>
>
> "foxtel employee" <foxtel.employee.xne09@no-mx.forums.eyo.com.au> wrote in
> message news:foxtel.employee.xne09@no-mx.forums.eyo.com.au...
> >
> > Hi All, (sorry its a bit late but might still help)
> >
> > Below is the fix for Searching for Signal and E34, E35 & Optus Aurora.
> >
> >
> > Here is an update on the fix for Searching for Signals
> >
> > Press Menu
> > Advanced options
> > Change dish installation
> > 9949
> > Signal setup
> > 1 (home)
> >
> > This should read as follows: If it doesn't please change using the
> > arrow buttons or number keypad on foxtel remote. Press OK once the
> > below settings have been added. Then press exit once. Then select Tune
> > & Re-scan and press OK. If an E16 appears after the Tune & Re-scan,
> > initialize the Smart Card.
> >
> > Signal source = enabled
> > LNB selection = 1
> > Freq = 12478
> > Symb rate 27800
> > Pol = Horizontal
> > FEC = 3/4
> >
> > *****Please check the LNB Setup by doing as follows
> >
> > Press Menu
> > Advanced options
> > Change dish installation
> > 9949
> > LNB Configuration
> > LNB Setup 1
> >
> > This should read as follows:
> >
> > LNB Power: On
> > LNB Mode: Single frequency
> > LNB Frequency: 11300 (for old 11.3 LNB or change to 10700 if you have
> > had new 10.7 LNB installed)
> >
> >
> > If you have had a tech out to your property anytime after 1st August
> > 2003 you will have a 10.7 LNB
> >
> >
> > E34, E35 & Optus Aurora fix
> > The output will change to 38 so please take a note of the customer's
> > output before performing this function
> > Menu
> > Advanced Options
> > Change Dish Install
> > Pin 9949
> > Reset to Factory Defaults
> > Press OK twice
> >
> > If you have any problems, let us know. 131 999 (its not busy anymore)
> >
> >
> > --
> > foxtel employee
> > ------------------------------------------------------------------------
> > foxtel employee's Profile:
> http://forums.eyo.com.au/member.php?action=getinfo&userid=7843
> > View this thread: http://forums.eyo.com.au/showthread.php?threadid=31448
> >
>
>